American Dynamics RAS916LS-1 Installation Guide

Browse online or download Installation Guide for Security cameras American Dynamics RAS916LS-1. American Dynamics RAS916LS-1 Installation guide User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 6
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
ADSDU8IOB / ADSDU8IOBW MOUNTING BASE 8200-0600-04, REV. A
INSTALLATION GUIDE
1 of 6
ADSDUIOB / ADSDUIOBW
Mounting Base Indoor
Installation
Installation Guide
Warnings and Cautions
Please review the following warnings and cautions
before you install the mounting base. For additional
warnings and cautions, see the camera dome
installation guide.
WARNINGS
WARNING!
ALWAYS USE:
Proper safety equipment for the location and
type of installation.
Proper lift equipment to reach the installation.
Safety features of the lift equipment.
BE SURE:
Electrical power is not connected to the dome
when connecting wires. Dome will move when
power is applied.
Electrical power is not connected to nearby
fixtures that you might touch during installation.
© 2006 Sensormatic Electronics Corp.
WARNING! DO NOT install this camera
dome in hazardous areas where highly
combustible or explosive products are
stored or used.
WARNING!
This dome runs on 24Vac. DO NOT
connect line voltage to this dome.
North America power requirements: In
North America, this device is intended to
be supplied from a Class 2 power supply.
For outdoor installations, use Class 3
wiring techniques, liquid-tight conduit, or
liquid-tight pipe.
This installation should be made by a
qualified service person and should
conform to all local codes.
WARNING! EU power requirements: This
product runs on 24Vac. In the EU, it is
intended to be powered from a Limited
Power Source. A limited power source is a
certified source of SELV, and if inherently
limited, with 8 amps maximum output
current, and a maximum of 100VA
available; or if not inherently limited, fused
with a maximum value of 3.3 Amps,
meeting section 2.11 of IEC950, and a
maximum of 250VA available. The power
supply can be obtained through American
Dynamics or through another source
where the provider can furnish the
verification. This is required to assure
electrical safety in the product.
Stromanforderungen in der EU: Dieses
Produkt wird mit 24 V Wechselstrom
betrieben. In der EU ist es für den Betrieb
durch eine begrenzte Stromquelle
vorgesehen. Eine begrenzte Stromquelle
ist eine zertifizierte SELV-Quelle
(Schutzkleinspannung), bei inhärenter
Begrenzung mit einem maximalen
Ausgangsstrom von 8 A und 100 VA
maximaler Verfügbarkeit, bei nicht
inhärenter Begrenzung mit einer
maximalen Sicherung von 3,3 A gemäß
Abschnitt 2.11 der IEC950 und 250 VA
maximaler Verfügbarkeit. Das Netzteil
kann über S American Dynamics oder eine
andere Quelle bezogen werden, wobei der
Anbieter den Nachweis der Konformität
bereitstellen sollte. Dies ist zur
Gewährleistung der elektrischen Sicherheit
des Produktes erforderlich.
Page view 0
1 2 3 4 5 6

Summary of Contents

Page 1 - Installation

ADSDU8IOB / ADSDU8IOBW MOUNTING BASE 8200-0600-04, REV. A INSTALLATION GUIDE 1 of 6 ADSDUIOB / ADSDUIOBW Mounting Base Indoor Installation Installat

Page 2

ADSDU8IOB / ADSDU8IOBW MOUNTING BASE 8200-0600-04, REV. A INSTALLATION GUIDE 2 of 6 Cautions • The maximum length of power cable allowed between th

Page 3 - Attaching to a Hard Ceiling

ADSDU8IOB / ADSDU8IOBW MOUNTING BASE 8200-0600-04, REV. A INSTALLATION GUIDE 3 of 6 Detaching the I/O Board To attach the mounting base, you must fi

Page 4 - Wiring the I/O Board

ADSDU8IOB / ADSDU8IOBW MOUNTING BASE 8200-0600-04, REV. A INSTALLATION GUIDE 4 of 6 Attaching to a Mounting Structure To attach the base to a mounti

Page 5 - INSTALLATION GUIDE

ADSDU8IOB / ADSDU8IOBW MOUNTING BASE 8200-0600-04, REV. A INSTALLATION GUIDE 5 of 6 SensorNet data connections Pin Color Designation 1-4 — Not used.

Page 6

ADSDU8IOB / ADSDU8IOBW MOUNTING BASE 8200-0600-04, REV. A INSTALLATION GUIDE 6 of 6 10. Check the LEDs on the I/O board to verify power and data ar

Comments to this Manuals

No comments