American Dynamics MegaPower 3200 Installation Guide Page 20
- Page / 86
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
MEGAPOWER CPU 8200-0421-03, REV. G
ADMINISTRATOR’S GUIDE
18 of 82
Retrieving Configuration Data
Do one of the following:
• For a new installation where no configuration data
file has been previously created, you should
initialize your system by retrieving (reading) into
EASY CPU the factory-default configuration data
residing in the CPU firmware. To do this, go to the
section,
Factory-Default or Existing
Configuration Data in CPU, below.
• If you want to use an existing configuration file
that already has been written to the CPU, go to
the section,
Factory-Default or Existing
Configuration Data in CPU, below.
• If you want to use an existing configuration file
that has not yet been written to the CPU, go to the
section,
Configuration Data File Only in PC.
• If you want to create a new configuration file and
then write it to the CPU, go to the section,
New
Configuration File, on page
20.
Factory-Default or Existing Configuration
Data in CPU
Retrieve the factory-default or existing configuration
data from the CPU into EASY CPU by doing the
following:
1. Click File on the main screen.
2. Click Read in the dropdown menu bar. The Read
from MPCPU dialog box appears.
Figure 41. Read from MPCPU dialog
3. In the Select MPCPU IP to Read From section of
the dialog box, select one of the following radio
buttons:
Note: Only one MPCPU radio button at a time can
be selected for reading.
• MPCPU A: Read from the MPCPU A IP
address as defined in the System – Options
dialog box. This IP address is read-only in
Figure 41. The default for this field is defined
in the Edit => Preferences menu option.
• MPCPU B: Read from the MPCPU B IP
address as defined in the System – Options
dialog box. This IP address is read-only in
Figure 41.
• User-specified IP: Enter an appropriate IP
address of your choosing. The default for this
field is defined in the Edit => Preferences
menu option.
4. In the MPCPU A, B, and Site No./Name as
specified in Sys => Options section, the Site No.
and Site Name fields only appear when either the
MPCPU A or MPCPU B radio buttons are
selected. They are for reference only and cannot
be changed in this dialog box. They are defined in
the System – Options dialog box.
5. Click the Read From Selected MPCPU button to
read the configuration from the selected MPCPU
IP address, or click Cancel to close the dialog
box without reading the configuration data.
6. Choose one of the following:
• If you want to enable user logins, go to the
section,
Adding a User Login, on page 21.
• If you do not want to enable user logins, your
system is ready to use.
Configuration Data File Only in PC
After creating and saving a configuration data file in
EASY CPU, you must write (or transfer) the new
configuration settings to the CPU.
To write an existing configuration data file located in
your PC to the CPU, do the following:
1. Click File on the main screen.
2. Click Open… in the dropdown menu bar.
3. Locate and highlight the desired file in the Open
dialog box.
4. Click Open. The file is loaded into EASY CPU.
5. Click File on the main screen.
6. Click Write in the dropdown menu bar. The Write
to MPCPU and/or Save Configuration To File
dialog box appears (
Figure 42).
- MegaPower 1
- Contents 4
- MegaPower CPU Front Panel 6
- MegaPower System 7
- Compatible System Keyboards 8
- System Features 8
- Administrator Tasks 9
- Operator Tasks 9
- Initializing the System 10
- Ethernet Network Connection 11
- Network DHCP Server 12
- Using a Static IP Address 13
- Firewall Setup 14
- Read Cycle 14
- Installing EASY CPU 15
- ADMINISTRATOR’S GUIDE 16
- Starting EASY CPU 18
- Viewing Configuration File 19
- Properties 19
- Data in CPU 20
- New Configuration File 22
- Adding a User Login 23
- Logging in Users for CPU 24
- Read/Write Access 24
- EASY CPU Main Screen 25
- Overview 25
- Checking the System 26
- Camera Status 27
- Passive Hot Switch Status 27
- Error Log Status 28
- Configuring the System 29
- Setting System Date and Time 30
- Setting Port Configurations 32
- Configuring the Dome/PTZ 32
- Device Direct Connection 32
- Configuring Switching 34
- Creating Tours 36
- Event Timers 37
- Event Timer – Tours 38
- Configuring Alarms 39
- Contact Arming 41
- Creating Alarm Monitor/ 42
- Contact Tables 42
- Defining System 44
- Devices 44
- Adding Camera Definitions 45
- Adding and Deleting Calling 46
- Contacts to Cameras 46
- Associating Salvo Callups to 47
- Cameras 47
- Defining Keyboards 48
- Adding a Range of Monitors 49
- Configuring Keyboard/User 50
- Keyboards and Priorities 50
- Priority Settings 51
- Controlling Access with 52
- Partitions 52
- Editing Camera Definitions 54
- Changing Calling Contacts 54
- Associating Keyboards to 55
- Adding Keyboard Definitions 56
- Editing Keyboard Definitions 56
- Adding Cameras to Keyboards 56
- Monitors 57
- Adding Monitor Access to 58
- Keyboards 58
- Adding Monitors to Keyboards 58
- Satellites 59
- Associating Monitors to 61
- Adding Monitor Definitions 62
- Adding a Range of Cameras 63
- Performing a Ping Test 64
- Declarations 65
- 64 of 82 66
- 65 of 82 67
- LCD Menu Structure 69
- F1 Special Function Keys 71
- F2 Special Function Keys 71
- Tables on page 40 for 73
- Alarm Receipt 75
- Alarm Arming and Response 75
- Alarm Display Indicators 75
- Alarm Display Method 76
- Alarm Queuing Method 76
- Alarm Clearance Method 76
- Single Display, Hold Queuing 78
- Block Display, Hold Queuing 79
- Queuing 79
- Satellite Site Connections 82
- 81 of 82 83
- 82 of 82 84
- 8200-0421-03 G 86
Related products and manuals for Processors American Dynamics MegaPower 3200
(38 pages)© 2020, manymanuals.com. All rights reserved. | 0.762 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals